C H A P T E R
1
Overview of Cisco IAD2430 Series IADs
This chapter provides a brief description of Cisco IAD2430 series integrated access devices and contains
the following sections:
•
•
•
•
•
•
Overview
The Cisco IAD2430 series integrated access devices (IADs) aggregate multiple channels of data and
voice or fax user-side traffic for transport over single or multiple wide-area network (WAN) uplinks.
Voice or fax traffic is transported by Voice over Internet Protocol (VoIP) or by Voice over Asynchronous
Transfer Mode (VoATM). All platforms support Media Gateway Control Protocol (MGCP), the signaling
protocol H.323, and Session Initiation Protocol (SIP).
Cisco IAD2430 series IADs support the following interfaces:
•
•
•
•
•
10/100BASE-T LAN connection
T1/E1 port connections
RJ-21 analog voice interface
WIC/VIC options
External/Internal compact flash
Cisco IAD2430 series IADs can be housed in a rack, mounted on a wall, or set on a benchtop surface.
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means by security. Statement
1017
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-1
Chapter 1 Overview of Cisco IAD2430 Series IADs
Overview
Cisco IAD2431-8FXS
THe Cisco IAD2431-8FXS provides eight analog FXS ports, two 10/100BASE-T ports, and one T1/E1
WAN port. The chassis has the following interfaces:
•
•
•
•
•
•
RJ-21 analog voice interface
One T1/E1 port
One 10/100BASE-T port
One WIC/VIC slot
External compact flash memory
AC and DC power inputs
Figure 1-3 Cisco IAD2431-8FXS Chassis
IAD2431-8FXS
Cisco IAD2431-16FXS
The Cisco IAD2431-16FXS provides sixteen analog FXS ports with two 10/100BASE-T ports and two
T1/E1 WAN ports. The chassis has the following interfaces:
•
•
•
•
•
•
RJ-21 analog voice interface
One T1/E1 port
Two 10/100BASE-T ports
One WIC/VIC slot
External compact flash memory
AC and DC power inputs
Figure 1-4 Cisco IAD2431 -16FXS
IAD2431-16FXS
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-3
Chapter 1 Overview of Cisco IAD2430 Series IADs
Overview
Cisco IAD2431-1T1E1
The Cisco IAD2431-1T1E1 provides one T1/E1 connection to a PBX, one T1/E1 WAN port, and two
10/100BASE-T ports. The chassis has the following interfaces:
•
•
•
•
•
Two T1/E1 ports
Two 10/100BASE-T ports
One WIC/VIC slot
External compact flash memory
AC and DC power inputs
Figure 1-5 Cisco IAD2431-1T1E1
IAD2431-1T1E1
Cisco IAD2432-24FXS
The Cisco IAD2432-24FXS provides 24 analog FXS ports, two 10/100BASE-T ports, and two T1/E1
WAN ports. The chassis has the following interfaces:
•
•
•
•
•
•
RJ-21 analog voice interface
Two T1/E1 ports
Two 10/100BASE-T ports
One WIC/VIC slot
External compact flash memory
AC and DC power inputs
Figure 1-6 Cisco IAD2432-24FXS
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-4
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
1-5
Chapter 1 Overview of Cisco IAD2430 Series IADs
Cisco IAD2430 Series Deployment
Cisco IAD2430 Series Deployment
integrated access devices.
Figure 1-8 Analog FXS User Interfaces with Metro Ethernet WAN Interface
Ethernet
RJ-21
IAD
Analog
telephones
Cisco IAD model number:
IAD2430-24FXS
Distribution
panel
Figure 1-9 T1/E1 WAN Interface with Analog FXS User Interfaces
Ethernet
T1
RJ-21
WAN
IAD
Analog
telephones
Cisco IAD model number:
IAD2431-8FXS
IAD2431-16FXS
IAD2432-24FXS
Distribution
panel
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-6
Chapter 1 Overview of Cisco IAD2430 Series IADs
Interfaces and Service Capabilities
Figure 1-10 WAN Interface with Analog FXS and FXO User Interfaces
WAN
IAD
Cisco IAD model number:
Cisco IAD2432-24FXS
with
Cisco VIC2-4FXO interface card
Figure 1-11 T1/E1 with T1/E1 Interface to PBX
Interfaces and Service Capabilities
•
•
•
Two administrative ports—One console and one auxiliary.
One or two 10/100BASE-T LAN ports.
The Cisco IAD2431 and Cisco IAD2432 IADs for T1/E1 WAN interface are equipped with one or
two T1/E1 WAN ports.
•
•
Cisco IAD2430 series IADs for analog voice user interface are equipped with an RJ-21 port for
connection to a distribution panel.
Cisco IAD2432 IADs for digital voice user interface are equipped with a T1/E1 port for connection
to a PBX.
Caution
All Cisco 2430 series IADs are customer premises equipment (CPE) only.
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-7
Chapter 1 Overview of Cisco IAD2430 Series IADs
Interfaces and Service Capabilities
Table 1-2 Cisco IAD2430 Series Interfaces and Service Capabilities
Port
Interface Configurations
Interface To
Services Supported
Details
Console
Port 0/0
EIA/TIA-232 asynchronous ASCII terminal
serial (DCE1)
1. DCE = data communications equipment
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-8
Chapter 1 Overview of Cisco IAD2430 Series IADs
Physical Description and LEDs
Physical Description and LEDs
All interface slots and LEDs are on the rear of the chassis.
Figure 1-12 Cisco IAD2430 Series IAD
1
2
3
6
4
5
8
7
9
11
12
13
10
1
2
3
4
5
Chassis ground connection
RJ-21 connector
T1/E1 port 1
6
7
8
9
WIC/VIC slot
11 DC power input1
10/100BASE-T port 1
10/100BASE-T port 0
AUX port
12 On/off switch
13 AC power input
T1/E1 port 0
Compact flash slot
10 Console port
1. This is not a redundant failover power supply connection. You must use either DC or AC.
Figure 1-13 Cisco IAD2400 Series LEDs
1
2
3
4
Table 1-3 Cisco 2430 Series IAD LEDs (Cisco 2432-24FXS shown)
No
1
LED/Color
Description
ACT—green
Green indicates activity; when any of the 24 voice ports is active in
a call (off hook) or one of the analog ports is in use
Status—green
Green when accessing IAD
2
CF (Slot 0)—green
Green when accessing read or write function
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-9
Chapter 1 Overview of Cisco IAD2430 Series IADs
Physical Description and LEDs
Product Serial Number Location for Cisco IAD2430 Series IADs
The serial number label for the Cisco IAD2430 Series IADs is located on the rear of the chassis, in the
Figure 1-14 Serial Number Locations
Note
The serial number for Cisco IAD2430 Series IADs is 11 characters long
Chassis Grounding
Chassis grounding is provided through the power cable, which uses a standard grounding plug. The
chassis is also equipped with two multi 4 x 0.7 screw terminals for chassis grounding. The accessory kit
contains a crimp-type ground lug that attaches to the two screw terminals. For more information, refer
to the
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-10
Chapter 1 Overview of Cisco IAD2430 Series IADs
Specifications
•
•
The slot for WICs and VICs is numbered slot 0. WIC and VIC interfaces are numbered by interface
with this slot number and an interface number, beginning with 0 and running from right to left.
FXS voice port numbering begins at 2/0 and extends to 2/7, 2/15, or 2/23, depending on the number
of voice ports.
Specifications
Table 1-4 Cisco IAD2430 Series IAD Technical Specifications
Characteristic
Dimensions
Value
1.75H x 17.5W x 13.5D in. (44.4 x 444.5 x 342.9 mm)
11 lb (4.106 kg) max
Weight
Input power
100 to 240 VAC, 1 A (max), 50 to 60 Hz, 70 W (max)
Maximum power surge
Input power
(DC 12-volt battery) by chassis
•
•
•
•
•
Cisco IAD2430-24FXS—60 W (204.7 BTU/h)
Cisco IAD2431-8FXS—50 W (170.6 BTU/h)
Cisco IAD2431-16FXS—60 W (204.7 BTU/h)
Cisco IAD2432-24FXS—70 W (238.8 BTU/h)
Cisco IAD2431-1T1E1—35 W (119.4 BTU/h)
Caution
Do not try to use AC and DC power at the same time. If you do, the unit stops
operating and you have to reboot using a single power source.
MTBF
•
•
•
•
•
Cisco IAD2430-24FXS—195,671 hours
Cisco IAD2431-8FXS—121,434 hours
Cisco IAD2431-16FXS—112,421 hours
Cisco IAD2432-24FXS—103,628 hours
Cisco IAD2431-1T1E1—126,118 hours
Operating environment
Nonoperating temperature
Operating humidity
Noise level
32 to 122°F (0 to 50°C)
–40 to 185°F (–40 to 85°C)
5 to 95%, noncondensing
55 dB @ 3 ft
Agency approvals
Refer to the Cisco IAD2400 Series Regulatory Compliance and Safety Information
document that accompanied your device for agency approvals.
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-11
Chapter 1 Overview of Cisco IAD2430 Series IADs
Software Elements
Software Elements
The operating system for Cisco IAD2430 series IADs is the Cisco IOS software that resides in flash
memory.
Configuration Connections
You can use an ASCII terminal or a PC to configure a Cisco IAD2430 series IAD. The configuration can
be performed in several ways:
•
•
•
Locally, with a direct connection through the console port
Remotely, with a connection through the auxiliary port and a modem
Through Telnet and TFTP
Configuration Methods
Automated Configuration
If your Cisco IAD2430 series IAD was ordered with the Simple Network-Enabled Auto-Provision
(SNAP) option, no on-site configuration is required. When the Cisco IAD is powered on and connected
to the WAN, the SNAP application downloads the applicable configuration files automatically. For
Cisco 2420 Series IAD feature module at the following URL:
Manual Configuration
When a Cisco IAD2430 series IAD is first installed, use the procedure in
Chapter 4, “Powering On Cisco IAD2430 Series IADs,” for the initial configuration. This sets the basic
communication parameters. After the Cisco IAD is operating and able to communicate, use the
procedures in the Cisco IAD2430 Series Software Configuration Guide to configure the specific services
and functions, or to make changes to the existing configuration.
There are multiple methods for configuring a Cisco IAD2430 series IAD:
•
•
•
•
•
System configuration dialog
Configuration mode—Cisco IOS software command-line interface (CLI)
Setup command facility—Remote configuration through a LAN or WAN
SNMP-based application—CiscoView or HP OpenView
HTTP-based configuration server—Provides access to the CLI from a web browser
Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide
OL-4234-05
1-12
|